Chemical Engineering Basics MCQ Questions & Answers | Chemical Engineering Page-9 section-10

Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Section 8 Section 9 Section 10 Section 11 Section 12 Section 13

81.
Draught produced by a tall chimney due to density difference between hot flue gas inside the Chimney and atmospheric air outside the chimney is more appropriately known as the __________ draught.

A. Natural

B. Induced

C. Forced

D. Chimney

Answer & Solution Discuss in Board Save for Later

82.
Pick out the wrong statement.

A. Weldability of high carbon steel is poorer compared to low carbon steel

B. Invar is a magnetic alloy

C. Magnetic permeability of the diamagenetic material is less than one

D. Martensitic transformation never goes to complection ( i.e., 100%) at room temperature

Answer & Solution Discuss in Board Save for Later

83.
The instrument based on the following principle is used for the measurement of oxygen only in the flue gases.

A. Chemical absorption

B. Thermal conductivity

C. Infrared absorption

D. Paramagnetism

Answer & Solution Discuss in Board Save for Later

84.
Colour comparator is used to measure the

A. pH value

B. Electrode potential

C. Colour intensity

D. None of these

Answer & Solution Discuss in Board Save for Later

85.
The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)

A. A

B. D

C. $$\frac{1}{{\text{A}}}$$

D. $$\frac{1}{{{{\text{A}}^2}}}$$

Answer & Solution Discuss in Board Save for Later

86.
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by

A. Conduction

B. Convection

C. Both A & B

D. Radiation

Answer & Solution Discuss in Board Save for Later

87.
Pearlite comprises of

A. 87% cementite & 13% Fe

B. 87% ferrite & 13% cementite

C. 93.33% ferrite & 6.67% C

D. 87% ferrite & 13% C

Answer & Solution Discuss in Board Save for Later

88.
Shrinkage allowance on pattern is provided to compensate for shrinkage when the

A. Metal changes from liquid state to solid state at freezing temperature

B. Solid phase temperature drops from freezing temperature to the room temperature

C. Liquid metal temperature drops from pouring temperature to room temperature

D. Liquid metal temperature drops from pouring temperature to freezing temperature

Answer & Solution Discuss in Board Save for Later

89.
Out of the following, the alloy which has equal percentage of constituents, is

A. White metal

B. Gun metal

C. Duralumin

D. Constanton

Answer & Solution Discuss in Board Save for Later

90.
Pick out the wrong statement.

A. Annealing twins are not observed in pure aluminium, because it has higher strain energy

B. Load during cold rolling can be lowered by the application of front tension

C. Very fine grain structure is desirable for high temperature creep application of materials

D. Soft magnetic materials are those which have less area within the hysterisis loop

Answer & Solution Discuss in Board Save for Later

1 2 3 4 5 6 7 8 9 10

Chemical Engineering Basics MCQ Questions & Answers | Chemical Engineering

81. Draught produced by a tall chimney due to density difference between hot flue gas inside the Chimney and atmospheric air outside the chimney is more appropriately known as the __________ draught.

Answer & Solution

82. Pick out the wrong statement.

Answer & Solution

83. The instrument based on the following principle is used for the measurement of oxygen only in the flue gases.

Answer & Solution

84. Colour comparator is used to measure the

Answer & Solution

85. The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)

Answer & Solution

86. Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by

Answer & Solution

87. Pearlite comprises of

Answer & Solution

88. Shrinkage allowance on pattern is provided to compensate for shrinkage when the

Answer & Solution

89. Out of the following, the alloy which has equal percentage of constituents, is

Answer & Solution

90. Pick out the wrong statement.

Answer & Solution

Read More Section(Chemical Engineering Basics)

81.
Draught produced by a tall chimney due to density difference between hot flue gas inside the Chimney and atmospheric air outside the chimney is more appropriately known as the __________ draught.

82.
Pick out the wrong statement.

83.
The instrument based on the following principle is used for the measurement of oxygen only in the flue gases.

84.
Colour comparator is used to measure the

85.
The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)

86.
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by

87.
Pearlite comprises of

88.
Shrinkage allowance on pattern is provided to compensate for shrinkage when the

89.
Out of the following, the alloy which has equal percentage of constituents, is

90.
Pick out the wrong statement.