Measurement And Instrumentation MCQ Questions & Answers

Section 1 Section 2 Section 3 Section 4

1.
One single phase wattmeter operating on 230V and 5A for 5 hours makes 1940 revolutions. Meter constant in revolutions is 400. What is the power factor of the land?

A. 1

B. 0.84

C. 0.73

D. 0.65

Answer & Solution Discuss in Board Save for Later

2.
The spring material used in a spring control device should have the following property.

A. Should be nonmagnetic

B. Most be of low temperature coefficient

C. Should have low specific resistance

D. All of the above

Answer & Solution Discuss in Board Save for Later

3.
Why is a MISC meter not recommended for DC measurement?

A. The meter is calibrated for AC and it’s error for DC would be high

B. The meter does not respond to DC signals

C. The error is high due to hysteresis effect

D. The error is high due to eddy current effect

Answer & Solution Discuss in Board Save for Later

4.
A moving iron ammeter may be compensated for frequency errors by

A. A shunt resistance

B. A series inductance

C. Shunt capacitance

D. Series resistance

Answer & Solution Discuss in Board Save for Later

5.
Which of the following meters has a linear scale?

A. Thermocouple meter

B. Moving iron meter

C. Hot wore meter

D. Moving coil meter

Answer & Solution Discuss in Board Save for Later

6.
For handling greater currents induction watt-meters are used in conjunction with

A. Potential transformers

B. Current transformers

C. Power transformers

D. Either of the above

Answer & Solution Discuss in Board Save for Later

7.
When using ohmmeter, applied voltage is to be disconnected from the circuit because

A. Voltage source will increase resistance

B. Current will decrease resistance

C. The ohmmeter has its own internal battery

D. None of the above

Answer & Solution Discuss in Board Save for Later

8.
A 10MHz CRO has

A. 5MHz sweep

B. 10MHz vertical oscillator

C. 10MHz horizontal oscillator

D. 10MHz supply frequency

Answer & Solution Discuss in Board Save for Later

9.
A CRO can display

A. AC signals

B. DC signals

C. Both AC and DC signals

D. Time invariant signals

Answer & Solution Discuss in Board Save for Later

10.
A galvanometer has

A. Air friction damping

B. Fluid friction damping

C. Spring coil damping

D. Eddy current damping

Answer & Solution Discuss in Board Save for Later

1 2 3 4 5 6 7 8 9 10

Measurement And Instrumentation MCQ Questions & Answers | ECE

1. One single phase wattmeter operating on 230V and 5A for 5 hours makes 1940 revolutions. Meter constant in revolutions is 400. What is the power factor of the land?

Answer & Solution

2. The spring material used in a spring control device should have the following property.

Answer & Solution

3. Why is a MISC meter not recommended for DC measurement?

Answer & Solution

4. A moving iron ammeter may be compensated for frequency errors by

Answer & Solution

5. Which of the following meters has a linear scale?

Answer & Solution

6. For handling greater currents induction watt-meters are used in conjunction with

Answer & Solution

7. When using ohmmeter, applied voltage is to be disconnected from the circuit because

Answer & Solution

8. A 10MHz CRO has

Answer & Solution

9. A CRO can display

Answer & Solution

10. A galvanometer has

Answer & Solution

Read More Section(Measurement and Instrumentation)

1.
One single phase wattmeter operating on 230V and 5A for 5 hours makes 1940 revolutions. Meter constant in revolutions is 400. What is the power factor of the land?

2.
The spring material used in a spring control device should have the following property.

3.
Why is a MISC meter not recommended for DC measurement?

4.
A moving iron ammeter may be compensated for frequency errors by

5.
Which of the following meters has a linear scale?

6.
For handling greater currents induction watt-meters are used in conjunction with

7.
When using ohmmeter, applied voltage is to be disconnected from the circuit because

8.
A 10MHz CRO has

9.
A CRO can display

10.
A galvanometer has