Manufacturing And Production Technology MCQ Questions & Answers | Mechanical Engineering

Home / Mechanical Engineering / Manufacturing And Production Technology

Section 1 Section 2 Section 3 Section 4 Section 5

41.
The facing is an operation of

A. Beveling the extreme end of a workpiece

B. Embossing a diamond shaped pattern on the surface of a workpiece

C. Reducing the diameter of a workpiece over a very narrow surface

D. Machining the ends of a workpiece to produce a flat surface square with the axis

Answer & Solution Discuss in Board Save for Later

42.
Threading is an operation of

A. Smoothing and squaring the surface around a hole

B. Sizing and finishing a small diameter hole

C. Producing a hole by removing metal along the circumference of a hollow cutting tool

D. Cutting helical grooves on the external cylindrical surface

Answer & Solution Discuss in Board Save for Later

43.
Quality screw threads are produced by

A. Thread milling

B. Thread chasing

C. Thread cutting with single point tool

D. Thread casting

Answer & Solution Discuss in Board Save for Later

44.
Ultrasonic machining is best suited for

A. Tool steels

B. Sintered carbides

C. Glass

D. All of these

Answer & Solution Discuss in Board Save for Later

45.
Which of the following parameters govern the value of shear angle in continuous chip formation?

A. True feed

B. Chip thickness

C. Rake angle of the cutting tool

D. All of these

Answer & Solution Discuss in Board Save for Later

46.
Surface grinding is done to produce

A. Tapered surface

B. Flat surface

C. Internal cylindrical holes

D. All of these

Answer & Solution Discuss in Board Save for Later

47.
The percentage of carbon in gray cast iron is in the range of

A. 0.25 to 0.75 percent

B. 1.25 to 1.75 percent

C. 3 to 4 percent

D. 8 to 10 percent

Answer & Solution Discuss in Board Save for Later

48.
Tool life is measured by the

A. Number of pieces machined between tool sharpenings

B. Time the tool is in contact with the job

C. Volume of material removed between tool sharpenings

D. All of the above

Answer & Solution Discuss in Board Save for Later

49.
The different spindle speeds on a lathe form

A. Arithmetical progression

B. Geometrical progression

C. Harmonical progression

D. Any one of these

Answer & Solution Discuss in Board Save for Later

50.
A better machinable metal is one which gives

A. Lower chip-tool contact area and larger shear angle

B. Higher chip-tool contact area and smaller shear angle

C. Lower chip-tool contact area and smaller shear angle

D. Higher chip-tool contact area and larger shear angle

Answer & Solution Discuss in Board Save for Later

1 2 3 4 5 6 7 8 9 10

Manufacturing And Production Technology MCQ Questions & Answers | Mechanical Engineering

41. The facing is an operation of

Answer & Solution

42. Threading is an operation of

Answer & Solution

43. Quality screw threads are produced by

Answer & Solution

44. Ultrasonic machining is best suited for

Answer & Solution

45. Which of the following parameters govern the value of shear angle in continuous chip formation?

Answer & Solution

46. Surface grinding is done to produce

Answer & Solution

47. The percentage of carbon in gray cast iron is in the range of

Answer & Solution

48. Tool life is measured by the

Answer & Solution

49. The different spindle speeds on a lathe form

Answer & Solution

50. A better machinable metal is one which gives

Answer & Solution

Read More Section(Manufacturing and Production Technology)

41.
The facing is an operation of

42.
Threading is an operation of

43.
Quality screw threads are produced by

44.
Ultrasonic machining is best suited for

45.
Which of the following parameters govern the value of shear angle in continuous chip formation?

46.
Surface grinding is done to produce

47.
The percentage of carbon in gray cast iron is in the range of

48.
Tool life is measured by the

49.
The different spindle speeds on a lathe form

50.
A better machinable metal is one which gives