Agricultural Engineering MCQ Question and Answer | Agriculture MCQ Question Page-1 section-7

Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7

1.
The air change required during hot weather to remove metabolic heat produced in livestock and poultry buildings is

A. One air change per minute or more

B. One air change per hour or more

C. Two air changes per hour or more

D. Four air changes per hour or more

Answer & Solution Discuss in Board Save for Later

2.
In normal conditions, a wind mill generates . . . . . . . . HP of power.

A. 5

B. 0.5

C. 0.1

D. 10

Answer & Solution Discuss in Board Save for Later

3.
The water horse power required to discharge the liquid through a sprayer at 30 lit/min. rate and 30 kg/cm² pressure will be

A. 3.5 hp

B. 4 hp

C. 2 hp

D. 2.5 hp

Answer & Solution Discuss in Board Save for Later

4.
Mould board was invented by

A. William Amos (England)

B. James Small (Scotland)

C. Thomas Jebberson (USA)

D. All together

Answer & Solution Discuss in Board Save for Later

5.
Width of cutof disc plough is increased by

A. Increasing disc angle

B. Increasing tilt angle

C. Addition of more weight

D. Decreasing disc angle

Answer & Solution Discuss in Board Save for Later

6.
Drop structures are used to control . . . . . . . . shaped gullies.

A. U

B. V

C. I

D. X

Answer & Solution Discuss in Board Save for Later

7.
Tilt angle of a disc plough is generally

A. 10°

B. 25°

C. 20°

D. 15°

Answer & Solution Discuss in Board Save for Later

8.
Fins are used into

A. Air cooling system

B. Water cooling system

C. Pressurized cooling system

D. All of the above

Answer & Solution Discuss in Board Save for Later

9.
Plough generally used for breaking impervious layer just below ploughing layers with help of number of tynes is called

A. Sub soiler

B. Chisel plough

C. Disc plough

D. Indegenous plough

Answer & Solution Discuss in Board Save for Later

10.
Peg type weeder is used in . . . . . . . . soils.

A. Clay

B. Loamy

C. Both A and B

D. None of the above

Answer & Solution Discuss in Board Save for Later

1 2 3 4 5

Agricultural Engineering MCQ Question and Answer | Agriculture MCQ Question

1. The air change required during hot weather to remove metabolic heat produced in livestock and poultry buildings is

Answer & Solution

2. In normal conditions, a wind mill generates . . . . . . . . HP of power.

Answer & Solution

3. The water horse power required to discharge the liquid through a sprayer at 30 lit/min. rate and 30 kg/cm2 pressure will be

Answer & Solution

4. Mould board was invented by

Answer & Solution

5. Width of cutof disc plough is increased by

Answer & Solution

6. Drop structures are used to control . . . . . . . . shaped gullies.

Answer & Solution

7. Tilt angle of a disc plough is generally

Answer & Solution

8. Fins are used into

Answer & Solution

9. Plough generally used for breaking impervious layer just below ploughing layers with help of number of tynes is called

Answer & Solution

10. Peg type weeder is used in . . . . . . . . soils.

Answer & Solution

Read More Section(Agricultural Engineering)

1.
The air change required during hot weather to remove metabolic heat produced in livestock and poultry buildings is

2.
In normal conditions, a wind mill generates . . . . . . . . HP of power.

3.
The water horse power required to discharge the liquid through a sprayer at 30 lit/min. rate and 30 kg/cm² pressure will be

4.
Mould board was invented by

5.
Width of cutof disc plough is increased by

6.
Drop structures are used to control . . . . . . . . shaped gullies.

7.
Tilt angle of a disc plough is generally

8.
Fins are used into

9.
Plough generally used for breaking impervious layer just below ploughing layers with help of number of tynes is called

10.
Peg type weeder is used in . . . . . . . . soils.