ExamVeda
Login
Home

Physical Metallurgy MCQ Questions and Answers | Metallurgical Engineering

Enhance your knowledge of Physical Metallurgy with this comprehensive collection of MCQ questions and answers. These MCQ questions and answers in Physical Metallurgy are specifically designed for students of Metallurgical Engineering who are preparing for the GATE Exam. Strengthen your preparation and excel in your studies with this valuable resource. Page-7 section-1

Each section contains 100 MCQs on Physical Metallurgy .
61
Dislocation cross-slip is difficult in those materials which have
Discuss
Answer & Solution
Answer: Option D
No explanation is given for this question. Let's Discuss on Board
62
The number of components is 2, the number of phases are 3 and degrees of freedom are 0. Then which of the following equilibrium is it?
Discuss
Answer & Solution
Answer: Option A
No explanation is given for this question. Let's Discuss on Board
63
In the hypothetical phase diagram, the melting point of each pure component is. 1000 K and the eutectic temperature is 800 K. The eutectic is located at the equi-atomic composition. The maximum solid solubility in α-phase is given by the mole fraction, Ne = 0.1.
The freezing range (in K) of the alloy with composition, Ne = 0.1 is
Physical Metallurgy mcq question image
Discuss
Answer & Solution
Answer: Option C
No explanation is given for this question. Let's Discuss on Board
64
With the increase in the degree of supercooling, the growth rate of a nucleus follows which one of the following trends?
Discuss
Answer & Solution
Answer: Option A
No explanation is given for this question. Let's Discuss on Board
65
Match the heat treatment process in Group I with resultant microstructure Group II.
Group I Group II
P. Martempering 1. Coarse pearlite
Q. Normalising 2. Fine pearlite
R. Sub-critical annealing for long time 3. Tempered martensite
S. Full annealing 4. Spheroidised cementite in the matrix of ferrite
Discuss
Answer & Solution
Answer: Option D
No explanation is given for this question. Let's Discuss on Board
66
Match the items in Group1 with those in Group2.
Group 1 Group 2
P. Fatigue 1. Cracking at extrusions and intrusions
Q. Hall-petch equation 2. Dislocation pile up
R. Creep 3. Slip and twinning
S. Plastic deformation 4. Grain boundary sliding
5. Angle of grain boundary
6. Young's modulus
Discuss
Answer & Solution
Answer: Option C
No explanation is given for this question. Let's Discuss on Board
67
Determine the correctness or otherwise of the following Assertion (a) and Reason (r).
Assertion (a): Peak aging time for an Al-4 wt.% Cu alloy is indicated by a maximum in the hardness.
Reason (r): The maximum volume fraction of the θ precipitates is formed at the peak aging time.
Discuss
Answer & Solution
Answer: Option A
No explanation is given for this question. Let's Discuss on Board
68
The stress required for Orowon dislocation bypass is 200 MPa in an alloy when the interprecipitate spacing is 500 nm. In the same alloy, if the inter-precipitate spacing is reduced to 200 nm, the stress required (in MPa) is
Discuss
Answer & Solution
Answer: Option C
No explanation is given for this question. Let's Discuss on Board
69
The self diffusion in FCC metals occurs by one of the following mechanisms.
Discuss
Answer & Solution
Answer: Option C
No explanation is given for this question. Let's Discuss on Board
70
A binary alloy system A-B shows the peritectic reaction, L + α (⟶β). An alloy of the peritectic composition when cooled under natural cooling conditions will show coring in
Discuss
Answer & Solution
Answer: Option B
No explanation is given for this question. Let's Discuss on Board