ExamVeda
Login
Home
1
A low ratio of the ac to the dc load impedance of a diode detector results in
Discuss
Answer & Solution
Answer: Option C
Solution:
Understanding Diode Detectors in Radio Receivers
Diode detectors are used in radio receivers to extract the audio signal from the radio frequency (RF) signal. They work by rectifying the RF signal, meaning they convert the alternating current (AC) signal into a direct current (DC) signal.

The detector's performance depends on the relationship between the AC load impedance (the impedance seen by the AC component of the signal) and the DC load impedance (the impedance seen by the DC component).

A low ratio of AC to DC load impedance means the AC impedance is much smaller than the DC impedance. This impacts how well the detector can handle the signal.

Imagine the detector trying to follow a quickly changing AC signal while also maintaining a steady DC level. If the AC impedance is too low, the detector struggles to accurately follow the rapid changes in the signal, which leads to distortion. The various options show different types of this distortion.

Therefore, a low ratio of AC to DC load impedance will cause negative-peak clipping. This is because the detector can't efficiently follow the negative portions of the AC signal, causing those portions to be "clipped" off. The other options, while possible problems in a radio receiver, aren't the direct result of a low AC-to-DC impedance ratio in the diode detector itself.
2
Indicate which of the following circuits could not demodulate SSB:
Discuss
Answer & Solution
Answer: Option D
Solution:
Definition of SSB (Single Sideband) Modulation:
SSB modulation is a form of amplitude modulation (AM) where only one of the sidebands (either the upper or lower) is transmitted, and the carrier is either suppressed or reduced to a very low level. This technique is used to save bandwidth and reduce power consumption. The demodulation of SSB signals requires extracting the modulated signal from one of the sidebands, which can be a complex process.

Option A: Balance modulator
A balance modulator is used to generate SSB signals by suppressing the carrier and one of the sidebands, making it suitable for SSB modulation. It works by mixing the signal with a local oscillator and then filtering out the unwanted frequencies. Balance modulators are capable of demodulating SSB signals, so this option is correct for SSB demodulation.

Option B: Product modulator
A product modulator operates by multiplying two signals (the carrier and the modulating signal), which can produce both upper and lower sidebands in AM. When used with proper filtering, a product modulator can demodulate SSB signals, as it can recover the modulating signal from the sideband. Therefore, this option is also correct for SSB demodulation.

Option C: BFO (Beat Frequency Oscillator)
A Beat Frequency Oscillator (BFO) is commonly used in SSB demodulation to reinsert a local carrier to the received SSB signal. By mixing the received signal with the BFO, the carrier is effectively reintroduced, allowing for the extraction of the original modulating signal. BFOs are specifically used in the demodulation of SSB signals, making this option correct as well.

Option D: Phase discriminator
A phase discriminator is typically used for demodulating phase-modulated (PM) or frequency-modulated (FM) signals. It works by detecting changes in the phase of the received signal. A phase discriminator is not designed to demodulate SSB signals, as SSB requires a different approach for signal recovery. Therefore, this option is incorrect for SSB demodulation.

Conclusion:
The phase discriminator (Option D) is the only circuit among the options that cannot demodulate SSB signals, as it is designed for phase modulation and frequency modulation, not for extracting sideband-modulated information in SSB.
3
If the intermediate frequency is very high (indicate false statement)
Discuss
Answer & Solution
Answer: Option D
Solution:
Intermediate Frequency (IF):
In radio receivers, the intermediate frequency (IF) is the frequency to which a carrier wave is shifted as part of the process of modulation and demodulation. It is used in superheterodyne receivers to simplify the processing of signals. The IF allows for better control over amplification and filtering.
Correct Answer Explanation:
The question asks about the effects when the intermediate frequency is very high. Let's break down each option:
Option A: Image frequency rejection is very good
This statement is false. In fact, when the intermediate frequency is very high, image frequency rejection tends to worsen. This is because the image frequency is more likely to fall close to the desired signal, making it harder for the receiver to distinguish between the two. Hence, a high IF generally complicates image frequency rejection, not improves it.
Option B: The local oscillator need not be extremely stable
This statement is false. In fact, when the IF is high, the local oscillator must be very stable. This is because the local oscillator frequency determines the IF, and any instability can cause errors in frequency conversion, leading to distortion or interference.
Option C: The selectivity will be poor
This statement is true. As the IF frequency increases, the selectivity (the ability of a receiver to isolate a specific signal from other frequencies) typically decreases. High IF frequencies make it harder to achieve narrow filtering bandwidths, reducing selectivity.
Option D: Tracking will be improved
This statement is true. Tracking refers to the ability of a receiver to follow changes in the input signal. When the IF is high, the receiver has a better ability to track signals over a broader frequency range, as the frequency conversion process is more sensitive to variations in the input signal.
Summary:
The false statement is Option A: "Image frequency rejection is very good," because a high intermediate frequency generally makes it more difficult to reject image frequencies.
4
One of the following cannot be used to demodulate SSB:
Discuss
Answer & Solution
Answer: Option D
Solution:
Single Sideband (SSB) modulation is a form of amplitude modulation (AM) where one of the sidebands is removed, leaving only one sideband (either upper or lower). Demodulating SSB requires a method to recover the original signal from the modulated carrier wave.

The correct answer is Option D: Complete phase-shift generator. A complete phase-shift generator is typically used for generating phase-shift keying signals and is not suitable for demodulating SSB signals. SSB demodulation typically requires a product detector or other balanced modulators to extract the original information from the modulated signal.

Why the other options are correct:
Option A: Product detector – A product detector is commonly used for demodulating both AM and SSB signals by multiplying the received signal with a local oscillator signal. It helps recover the original audio or information signal from the modulated carrier.

Option B: Diode Balance modulator – A diode-balanced modulator can be used for SSB demodulation by performing a similar function as the product detector, where the signal is mixed with a local oscillator to recover the baseband signal.

Option C: Bipolar transistor balanced modulator – A bipolar transistor balanced modulator is also suitable for demodulating SSB signals, as it can mix the received SSB signal with a local oscillator signal to reconstruct the original message.
5
Indicate which of the following statements about the advantages of the phase discriminator over the slope detector is false:
Discuss
Answer & Solution
Answer: Option C
Solution:
A phase discriminator is a type of demodulator used in communication systems, particularly for phase modulation (PM). It converts the phase variation of the received signal into an amplitude variation that can be easily detected. A slope detector, on the other hand, is used for frequency demodulation and detects frequency deviations by looking at the slope of the frequency response.

The correct answer is Option C: Greater limiting. A phase discriminator does not provide greater limiting compared to a slope detector. Limiting refers to the process of reducing the effect of amplitude variations in the received signal, ensuring that the demodulator only reacts to the phase or frequency variation. Slope detectors are generally better at limiting because they can handle amplitude variations more effectively than phase discriminators.

Why the other options are correct:
Option A: Much easier alignment – Phase discriminators are generally easier to align than slope detectors because they are less sensitive to variations in signal amplitude, making the alignment process more straightforward.

Option B: Better linearity – Phase discriminators tend to have better linearity over a wider range of input frequencies, meaning the relationship between input phase and output signal is more consistent compared to slope detectors.

Option D: Fewer tuned circuits – Phase discriminators typically require fewer tuned circuits than slope detectors, which often require more complex circuitry to ensure proper frequency response for demodulation.
6
The controlled oscillator synthesizer is sometimes preferred over the direct one because
Discuss
Answer & Solution
Answer: Option B
Solution:
The controlled oscillator synthesizer is sometimes preferred over the direct one because of its improved frequency stability. Let’s break this down in more detail.

Controlled Oscillator Synthesizer:
A controlled oscillator synthesizer is a type of frequency synthesizer where the output frequency is controlled by a reference signal, often a voltage-controlled oscillator (VCO). This system allows for the generation of a wide range of frequencies with high precision.

Direct Oscillator Synthesizer:
On the other hand, a direct oscillator synthesizer generates frequencies by directly using a single oscillator and typically relies on components like crystals to define the output frequency.

Explanation of the Correct Answer:
Option B: Its frequency stability is better
The controlled oscillator synthesizer is preferred over the direct one primarily because it offers better frequency stability. This means that it maintains a consistent frequency output over time, even when external factors like temperature, voltage variations, or aging affect the system. The voltage-controlled oscillator in the controlled synthesizer is designed to be highly stable, often incorporating advanced feedback mechanisms that regulate frequency fluctuations. As a result, these synthesizers can offer superior performance in applications where precise and stable frequencies are critical, such as in communication systems and signal processing.

Other Options:
Option A: It is a simpler piece of equipment
This option is not correct. The controlled oscillator synthesizer is generally more complex due to the need for additional components such as feedback systems and voltage-controlled oscillators. In contrast, a direct oscillator synthesizer might be simpler, using fewer components for frequency generation.

Option C: It does not require crystal oscillator
While it is true that some controlled oscillator synthesizers do not rely directly on a crystal oscillator, this is not the main reason they are preferred. The focus is on the stability and flexibility of the frequency output rather than the type of oscillator used. Many controlled oscillators still use crystals for frequency references, but they are designed to be less susceptible to instability.

Option D: It is relatively free of spurious frequency
While controlled oscillator synthesizers may have fewer spurious frequencies than direct ones, this is not their primary advantage. Spurious frequencies, which are unwanted signals at frequencies different from the intended one, can still be present in both types of systems. However, controlled oscillator synthesizers are more likely to mitigate this issue due to their frequency stability and better design features for filtering and regulation.

In conclusion, the controlled oscillator synthesizer is preferred because of its superior frequency stability (Option B), which ensures more reliable performance, especially in sensitive applications.
7
A superheterodyne receiver with an IF of 450 kHz is tuned to a signal at 1200 kHz. The image frequency is
Discuss
Answer & Solution
Answer: Option D
Solution:
Superheterodyne Receiver: A superheterodyne receiver is a type of radio receiver that uses a mixer to convert a radio frequency (RF) signal to a fixed intermediate frequency (IF). This IF signal is then amplified and demodulated to extract the audio signal.

Intermediate Frequency (IF): The intermediate frequency (IF) is a fixed frequency to which the received radio frequency (RF) signal is converted in a superheterodyne receiver. This allows for efficient amplification and filtering of the signal before demodulation.

Image Frequency: The image frequency is an unwanted signal that can also produce the same IF frequency as the desired signal. It occurs because the mixer in a superheterodyne receiver is essentially a non-linear device which produces sum and difference frequencies. The image frequency is always offset from the desired signal frequency by twice the IF.

Calculating Image Frequency: In this question, the desired RF signal is at 1200 kHz, and the IF is 450 kHz. The image frequency (fimage) can be calculated using the following formula:

fimage = fRF ± 2 * fIF

Where:
fRF is the radio frequency (1200 kHz)
fIF is the intermediate frequency (450 kHz)

Using the formula:

fimage = 1200 kHz + 2 * 450 kHz = 2100 kHz
or
fimage = 1200 kHz - 2 * 450 kHz = 300 kHz (This is not among the options)

Therefore, the image frequency is 2100 kHz (Option D).

8
The local oscillator of a broadcast receiver is tuned to a frequency higher than the incoming frequency
Discuss
Answer & Solution
Answer: Option C
Solution:
The question is about the tuning of the local oscillator in a broadcast receiver and why it is tuned to a frequency higher than the incoming frequency. Let's break this down.

Local Oscillator in Radio Receivers:
In radio receivers, the local oscillator (LO) is an electronic oscillator used to convert the incoming radio frequency (RF) signal to an intermediate frequency (IF). The local oscillator produces a frequency that is mixed with the incoming signal to create a frequency that can be more easily processed by the receiver’s circuits. This frequency mixing process is known as heterodyning.

Intermediate Frequency (IF):
The intermediate frequency (IF) is a fixed frequency that is used for easier signal processing. It is derived by mixing the local oscillator frequency with the received signal. The choice of IF allows the receiver to have more stable and simpler amplification and filtering circuits.

Explanation of the Correct Answer:
Option C: Because otherwise an intermediate frequency could not be produced
The correct answer is Option C. The reason the local oscillator is tuned to a frequency higher than the incoming frequency is to create the necessary intermediate frequency (IF). When the local oscillator frequency is set higher than the incoming frequency, the difference between the two frequencies results in a fixed IF. This IF is easier to process for amplification and filtering, which is essential for the proper functioning of the receiver. If the local oscillator were not tuned higher, it would be impossible to generate this intermediate frequency through mixing.

Other Options:
Option A: To help the image frequency rejection
This option is not correct. The rejection of the image frequency is important in superheterodyne receivers, but it is not directly related to tuning the local oscillator higher. The image frequency rejection is typically handled by employing additional filtering and design techniques in the receiver circuitry, rather than simply tuning the local oscillator higher.

Option B: To permit easier tracking
This option is also incorrect. Tracking refers to the ability of the receiver’s circuits to follow the varying frequencies of a station. While easier tracking is important in some contexts, tuning the local oscillator higher than the incoming frequency is done for the purpose of generating the intermediate frequency (IF), not specifically for tracking.

Option D: To allow adequate frequency coverage without switching
This option is not correct either. The local oscillator is tuned higher than the incoming frequency to generate the intermediate frequency, not to avoid switching between frequencies. Frequency coverage and tuning strategies are achieved through the overall design of the receiver circuits, not by simply setting the local oscillator frequency in a particular way.

In conclusion, the local oscillator is tuned to a frequency higher than the incoming frequency to produce the intermediate frequency (IF) (Option C), which simplifies the subsequent stages of signal processing in the receiver.
9
Show which of the following statements about the amplitude limiter is untrue:
Discuss
Answer & Solution
Answer: Option A
Solution:
The amplitude limiter is a circuit designed to limit the amplitude of an input signal to a specific threshold. It helps in preventing distortion by restricting the output signal level, even when the input level increases beyond a certain point. Now, let’s analyze each of the options presented:

Option A: The circuit is always biased in class C, by virtue of the leak-type bias.
This statement is untrue. The class of biasing (whether class A, B, or C) depends on the specific circuit design and the way the components are arranged. While a leak-type bias might be used in some circuits, it does not necessarily imply that the circuit is always biased in class C. Class C biasing is typically used for high-frequency operation, and it is not a requirement for all amplitude limiters.

Option B: When the input increases past the threshold of the limiting, the gain decreases to keep the output constant.
This statement is true. The purpose of an amplitude limiter is to keep the output signal at a constant level, regardless of how much the input signal increases. When the input exceeds the threshold, the gain of the circuit is reduced to prevent the output from rising any further, ensuring that it stays within the desired range.
Option C: The output must be tuned.
This statement is not necessarily true. While some amplitude limiters may require tuning, especially in certain radio receiver applications, not all limiters need to be tuned. The function of the amplitude limiter is more about controlling the signal level rather than tuning the output signal. Therefore, the output does not have to be tuned in every case.

Option D: Leak-type bias must be used.
This statement is incorrect. While leak-type bias is used in some circuits for biasing, it is not a mandatory feature for all amplitude limiters. The use of leak-type bias depends on the specific circuit design, but it is not a strict requirement for the function of the amplitude limiter.

In summary, the untrue statement is Option A, as the use of class C biasing is not a universal characteristic of amplitude limiters.
10
A receiver has poor IF selectivity. It will therefore also have poor
Discuss
Answer & Solution
Answer: Option A
Solution:
IF Selectivity: Intermediate Frequency (IF) selectivity refers to the ability of a receiver's intermediate frequency amplifier to select the desired signal and reject adjacent unwanted signals. A receiver's IF stage is crucial for filtering out interfering signals that are close in frequency to the desired signal after it has been downconverted from the Radio Frequency (RF).

Poor IF Selectivity: If the IF selectivity is poor, it means the IF amplifier is not effectively filtering out adjacent channel signals. This allows unwanted signals to pass through, leading to various reception problems.

Correct Answer: A. Blocking
Blocking occurs when a strong, out-of-band signal overwhelms the receiver's IF amplifier, affecting the amplification and demodulation of the desired signal. Poor IF selectivity directly contributes to blocking because the filter isn't rejecting the strong, interfering signal sufficiently. The strong signal essentially "blocks" the desired signal from being properly processed.

Why other options are less likely:
B. Double-spotting: Double-spotting is a phenomenon where a single strong signal appears at two different points on the frequency scale. This is typically caused by image response or other frequency-related issues, but not directly by poor IF selectivity alone.

C. Diversion reception: Diversion reception refers to the reception of an unwanted signal that is outside the normal tuning range. This may be due to insufficient RF filtering or other issues, but not specifically poor IF selectivity.

D. Sensitivity: Sensitivity refers to the minimum signal strength a receiver needs to detect. While poor IF selectivity can indirectly affect sensitivity by introducing interference which could mask weak signals, it's not its primary effect. Poor IF selectivity's main impact is on the receiver's ability to reject unwanted signals close to the desired signal, leading to problems like blocking.