Process Equipment And Plant Design MCQ Questions & Answers

Process Equipment And Plant Design MCQ Questions & Answers | Chemical Engineering

Learn Process Equipment And Plant Design MCQ questions & answers are available for a Chemical Engineering students to clear GATE exams, various technical interview, competitive examination, and another entrance exam. Process Equipment And Plant Design MCQ question is the important chapter for a Chemical Engineering and GATE students. Page-3 section-1

Shortest distance between two tubes is

A) Called tube pitch B) Called tube clearance C) More in case of triangular pitch as compared to square pitch of tube layout D) None of these

Discuss

Answer & Solution

Answer: Option B

No explanation is given for this question. Let's Discuss on Board

$$\frac{{{{\text{L}}_{\text{e}}}}}{{\text{D}}}$$ for a Tee (used as elbow, entering run) would be around

A) 5 B) 60 C) 200 D) 350

Discuss

Answer & Solution

Answer: Option B

No explanation is given for this question. Let's Discuss on Board

A rivetted joint does not fail by __________ of rivets.

A) Tearing B) Shearing C) Tearing of the plate across a row D) None of these

Discuss

Answer & Solution

Answer: Option D

No explanation is given for this question. Let's Discuss on Board

Overall mass transfer co-efficient in case of absorption of __________ in water is based on the gas film co-efficient only, as the mass transfer process is gas film (phase) controlling.

A) CO₂ B) SO₂ C) NH₃ D) None of these

Discuss

Answer & Solution

Answer: Option C

No explanation is given for this question. Let's Discuss on Board

__________ dished head is the strongest of all.

A) Hemispherical B) Elliptical C) Torispherical D) None of these

Discuss

Answer & Solution

Answer: Option A

No explanation is given for this question. Let's Discuss on Board

Value of Peclet number = ∞, is the representative of

A) Laminar flow B) Complete back mixing C) Plug flow D) Eddy diffusivity = 0

Discuss

Answer & Solution

Answer: Option C

No explanation is given for this question. Let's Discuss on Board

For identical operating conditions, the pressure drop over __________ tray is the highest out of the following.

A) Sieve B) Valve C) Counterflow D) Bubble cap

Discuss

Answer & Solution

Answer: Option D

No explanation is given for this question. Let's Discuss on Board

The normal range of velocity of steam in pipes is __________ m/sec.

A) 0.1-0.5 B) 1-5 C) 10-20 D) 80-100

Discuss

Answer & Solution

Answer: Option D

No explanation is given for this question. Let's Discuss on Board

For turbulent flow (NRe > 2100) of low viscosity fluid (μ > 20cp) in steel pipes, the optimum inside pipe diameter is given by (where, Q = fluid flow rate, ft³/sec.ρ = fluid density, lb/ft³.μ = fluid viscosity, centipoise D_i = optimum inside pipe diameter, inches)

A) D_{i, opt} = 3.9 Q^0.45.ρ^0.13 B) D_{i, opt} = 3.9 Q^0.45.μ^0.95 C) D_{i, opt} = 4.7 Q^0.36.μ^3.2ρ^0.13 D) D_{i, opt} = 3 Q^0.36.μ^0.88

Discuss

Answer & Solution

Answer: Option A

No explanation is given for this question. Let's Discuss on Board

Rate of filtrate delivery is inversely proportional to the

A) Filtering area & the pressure difference driving force B) Viscosity of filtrate C) Cake & filter medium resistance D) Both A & B

Discuss

Answer & Solution

Answer: Option D

No explanation is given for this question. Let's Discuss on Board